故障产生与修复表

　　故障产生与修复表
　　创建
　　Flexsim软件中的故障产生与修复表主要用来模拟设备的设备故障。
　　The fault generation and repair table in the Flexsim software is mainly used to simulate the equipment failure of the equipment.
　　关于故障产生与修复表的创建有两种基本方式，第一种是通过工具箱直接创建，第二种是在实体中创建，具体操作如下
　　There are two basic ways to create a fault generation and repair table. The first is to create directly through the toolbox, and the second is to create in the entity. The specific operations are as follows
　　其中故障产生与修复表的名称软件是有给定的其中MTBF全程为平均故障间隔事件，指系统两次故障间隔时间段的平均值，通常服从某个期望值的指数分布；MTTR全程为平均修复时间，指系统从发生故障到维修结束时间段的平均值，通常服从均匀分布。
　　The name software of the fault generation and repair table is given. The whole MTBF is the mean time between failures, which refers to the average time between two failures of the system, which usually obeys an exponential distribution of an expected value; the whole MTTR is the mean repair time , Refers to the average value of the time period from the failure of the system to the end of the maintenance, which usually obeys a uniform distribution.
　　介绍
　　表的基本函数包括，第一次故障时间，修理时间，故障间隔时间以及之前有讲过的中断函数以及恢复函数。表格的运行逻辑便是开始工作时间，一直运行到第一次故障时间，所有成员及实体便会触发中断函数以及中断触发，然后进入一段修复时间，直到触发恢复函数及恢复触发，然后就会进入一段故障间隔时间，修复时间以及故障间隔时间，并不断反复。
　　The basic functions of the table include the first failure time, repair time, failure interval time, and the interrupt function and recovery function that have been mentioned before. The running logic of the table is the starting working time. It runs until the first failure time. All members and entities will trigger the interrupt function and the interrupt trigger, and then enter a period of repair time, until the recovery function is triggered and the recovery trigger, and then it will enter A period of time between failures, repair time and time between failures, and repeated.
　　模型
　　接下来用一个非常简单的模型为大家演示一下，故障产生与修复表的运行作用及现象，我们随便设置表中的函数时间间隔，我们把第一次故障时间设为30秒，修理时间设置为40秒，故障间隔时间设置为120秒，也就是当运行到第30秒的时候便会发生故障，到70秒的时候就会恢复，继续运行，然后190秒的时候便会进入下一次故障。具体运行效果如下图所示
　　Next, I will use a very simple model to demonstrate the operation effect and phenomenon of the fault generation and repair table. We randomly set the function time interval in the table. We set the first failure time to 30 seconds and the repair time to 40 seconds, the failure interval time is set to 120 seconds, that is, when it runs to the 30th second, it will fail, and it will resume at 70 seconds, continue to run, and then enter the next failure at 190 seconds. The specific operation effect is shown in the figure below
　　相通
　　故障产生与修复表和时间表有很多相似的地方，我们也可以利用时间表来进行故障产生与修复，关于时间表的创建我就不再赘述，我们可以直接选择不重复时间表，只需要找到中断类型为故障就可以了，然后设置好对应的时间便可以当作故障产生与时间表使用，让我们一起来看看效果吧
　　There are many similarities between the fault generation and repair tables and timetables. We can also use the timetable for fault generation and repair. I will not repeat the creation of the timetable. We can directly choose not to repeat the timetable, just find The interrupt type is fault, and then set the corresponding time can be used as fault generation and timetable, let us take a look at the effect.
　　参考资料：哔哩哔哩小付同学
　　英文翻译：Google翻译
　　本文由LearningYard学苑原创，部分资料来源于网络，若有侵权，请联系删除。